Kontakti

Na voljo smo vam od ponedeljka do petka med 8:00 in 17:00 uro. Na tej povezavi najdete kontaktne osebe za svojo regijo.

Centrala Wolfurt
+43 5574 6706-0

Vaša kontaktna oseba

Košarica {{ (warenkorbCtrl.warenkorb.bestellNummer ? (' [' + warenkorbCtrl.warenkorb.bestellNummer + '] ') : '' )}} | {{warenkorbCtrl.warenkorb.items.length}} izdelek   Zamenjaj košarico

Opomba

Slika izdelek Kos Cene po pozicijah Skupna cena Skupna cena s popustom
{{warenkorbItem.produktgruppe.produktname}}

{{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben:[{attrPrefix: 'L_', searchPattern: '/...', replacePrefix: '/', replaceSuffix: ''}] }} {{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben}}

{{attributwertEingabe.attributBezeichnung}}

     
{{hannexItem.Benennung}}

{{hannexItem.Bezeichnung}}

     

Prosimo vas, da se prijavite, da bi lahko videli vaše cene ter nadaljevali z naročilom.

Sporočila za javnost o našem podjetju

Zanimate se za naše podjetje in naše izdelke? Potem ste tukaj pravilno.

Reliable demoulding of complex injection moulded parts

08.11.2016, Mould making

The compact ejector accelerator from Meusburger is the ideal device for the safe and targeted ejection of complex parts: a single ejector is additionally accelerated by which snagging of the injection moulded part is avoided. The injection pressure is absorbed by the ejector base plate thus the ejection accelerator does not bear any load and has a longer service life. Due to the small component size a flexible positioning of the ejector accelerator in the ejector set is also possible when retrofitting.

 

The E 1522 Ejector accelerator from Meusburger optimises the smooth ejection of injection moulded parts. With the newly developed component targeted control of the ejection process is possible. Through the additional acceleration of a single ejector snagging of the injection moulded part is avoided. The acceleration ratio is 1:1.5. Therefore a longer path is achieved with a small stroke. The repositioning of the accelerator does not take place directly through the clamp plate but through a cut to length ejector so the same buffer plates for the ejector set can be used. A further advantage is that the entire injection pressure is absorbed directly by the ejector base plate. As a result the ejector accelerator does not bear any load during the injection moulding process.
The three different sizes available allow designers to install ejectors in the diameters of 3 – 11.5 mm at will. The small component size enables a flexible positioning of the ejection accelerator in the ejector set. Therefore the ejector accelerator can also be installed quickly and easily when retrofitting the mould. In order to save design time, the installation space is already included in the CAD data. As usual with Meusburger the new component is available from stock.

 

 

K pregledu novic

Press contact

Should you require further information on this press release or have any questions or comments, please feel free to contact us by email.

Susanne Zukowski
Komunikacija / PR

+43 5574 6706-1736

E-Mail

Prijava

Ste že registriran uporabnik?

V kolikor že imate dostop za prijavo v Meusburger portal se prosimo prijavite tukaj:

Ste pozabili geslo?

Novo generirano geslo je že na poti in bo kmalu v vašem poštnem predalu. Želimo Vam uspešen dan.

Prosimo vnesite vaš E-mail naslov.
Poslali vam bomo novo geslo.

Izberite vašo državo

Lokacije

Try our new version of 'My account'

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Keep selection
Beta
New version
Current version