Kontakti

Na voljo smo vam od ponedeljka do petka med 8:00 in 17:00 uro. Na tej povezavi najdete kontaktne osebe za svojo regijo.

Centrala Wolfurt
+43 5574 6706-0

Vaša kontaktna oseba

Košarica {{ (warenkorbCtrl.warenkorb.bestellNummer ? (' [' + warenkorbCtrl.warenkorb.bestellNummer + '] ') : '' )}} | {{warenkorbCtrl.warenkorb.items.length}} izdelek   Zamenjaj košarico

Opomba

Slika izdelek Kos Cene po pozicijah Skupna cena Skupna cena s popustom
{{warenkorbItem.produktgruppe.produktname}}

{{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben:[{attrPrefix: 'L_', searchPattern: '/...', replacePrefix: '/', replaceSuffix: ''}] }} {{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben}}

{{attributwertEingabe.attributBezeichnung}}

     
{{hannexItem.Benennung}}

{{hannexItem.Bezeichnung}}

     

Prosimo vas, da se prijavite, da bi lahko videli vaše cene ter nadaljevali z naročilom.

Zmanjševanje napetosti

Naš izbran nabor omogoča za skoraj vsak primer uporabe ustrezen material.

1.1730 Tool steel

Designation

DIN:C 45 U
AFNOR:XC 48
UNI:-
AISI:1045


Chemical composition:

C0.45
Si0.30
Mn0.70

Strength:

max. 215 HB
(≈ 710 N/mm²)

Thermal conductivity at 20 °C:

50 W/m K


Character:

unalloyed tool steel with excellent machinability, good core toughness for minor applications; chilled cast steel, suitable for flame and inductive hardening

Application:

unhardened parts for mould, die and jig construction; plates and frames for mould bases and die sets


Treatment by

unusual:
Polishing, etching, EDM, nitriding, hard chroming

 


Heat treatment:

Soft annealing:
 680 to 710 °C for about 2 to 5 hours
 slow controlled cooling of 10 to 20 °C per hour to about 600 °C;
 further cooling in air, max. 190 HB

Hardening:
 800 to 830 °C
 Quenching in oil/hot bath/air
 Obtainable hardness: 58 HRC
 hardening depth 3−5 mm
 max. 15 mm through hardening thickness

Tempering:
 Slow heating to tempering temperature immediately after hardening, to 180 to 300 °C depending on desired hardness
 1 hour per 20 mm: min. 2 hours

 

Annealing graph:

To the mould making overview To the die making overview

Available in the web shop as:
Data sheet 1.1730

Odpri PDF

Material grades brochure

Material grades brochure

Material grades poster

Material grades poster

Prijava

Ste že registriran uporabnik?

V kolikor že imate dostop za prijavo v Meusburger portal se prosimo prijavite tukaj:

Ste pozabili geslo?

Novo generirano geslo je že na poti in bo kmalu v vašem poštnem predalu. Želimo Vam uspešen dan.

Prosimo vnesite vaš E-mail naslov.
Poslali vam bomo novo geslo.

Izbira trgovine

Izberite vašo državo

Lokacije

Try our new version of 'My account'

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Keep selection
Beta
New version
Current version