Contact

Vă stăm la dispoziție personal cu cea mai mare plăcere de luni până vineri între orele 8:00 și 17:00. Pe acest link ve-ți regăsi persoana de contact din regiunea dumneavoastră.

Centrala Wolfurt
+43 5574 6706-0

Persoana dvs. de contact

Coş de cumpărături {{ (warenkorbCtrl.warenkorb.bestellNummer ? (' [' + warenkorbCtrl.warenkorb.bestellNummer + '] ') : '' )}} | {{warenkorbCtrl.warenkorb.items.length}} Articol   Schimbare coș cumpărături

Observație

Poză Articol Buc Preț unitar Preț total Preț total incl. reducere
{{warenkorbItem.produktgruppe.produktname}}

{{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben:[{attrPrefix: 'L_', searchPattern: '/...', replacePrefix: '/', replaceSuffix: ''}] }} {{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben}}

{{attributwertEingabe.attributBezeichnung}}

     
{{hannexItem.Benennung}}

{{hannexItem.Bezeichnung}}

     

Vă rugăm să vă logați pentru a vedea prețurile și pentru a continua comanda.

Reducerea tensiunii

Sortimentul nostru bine selectat are materialul potrivit pentru aproape fiecare aplicație.

1.2311 Tool steel

Designation

DIN:40 CrMnMo 7
AFNOR:40 CMD 8
UNI:35 CrMo 8 KU
AISI:P20

Chemical composition:

C0.40
Si0.40
Mn1.50
Cr1.90
Mo0.20

Strength:

280 - 325 HB
(≈ 950 - 1100 N/mm²)

Thermal conductivity at 100 °C:

35 W/m K


Character:

alloyed and pre-toughened tool steel, especially suitable for polishing and nitriding; high dimensional stability

Application:

cavity plates, inserts and high-tensile machine parts


Treatment by

possible:
Etching, EDM

Polishing:
excellent polishing; for higher surface requirements we recommend steel for through hardening

Nitriding:
increases the steel's wear resistance

Hard chroming:
particularly increases the steel's wear resistance and corrosion resistance


Heat treatment:

already pre-toughened; usually no heat treatment required

Nitriding:
Before nitriding, stress-relief annealing is recommended at 580 °C. (Meusburger standard)

Hard chroming:
After the hard chroming the mould must be annealed about 3 to 4 hours at 180 °C to avoid brittle fractures from hydrogen.

Hardening:
840 to 860 °C

Cooling:
to 180 °C/220 °C in oil/hot bath, then in air to about 100 °C obtainable hardness: 52 HRC

Tempering:
Slow heating to tempering temperature immediately after hardening. Minimum time in furnace: 1 hour per 25 mm part thickness

Annealing graph:


Technical tip:

  • Core strength decreases with increasing plate thickness ⇒ for thickness >300, 1.2738 is recommended.

To the mould making overview To the die making overview

Available in the web shop as:
Data sheet 1.2311

Deschide PDF

Material grades brochure

Material grades brochure

Material grades poster

Material grades poster

Log in

Sunteți deja client?

Dacă aveți deja date de acces pentru Portalul Meusburger, vă rugăm să vă logați aici:

Ați uitat parola?

Parola nouă este deja pe drum și trebuie să apară în scurt timp în căsuța dvs. de email. Vă dorim o zi de succes.

Vă rugăm să introduceți adresa dvs. de e-mail.
Vă vom trimite o parolă nouă.

Selecţie shop

Alegeți țara

Locații

Try our new version of 'My account'

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Keep selection
Beta
New version
Current version