Kapcsolat

Hétfőtől péntekig 8:00 és 17:00 között szívesen személyesen is állunk rendelkezésére. Ezen a linken keresztül találja meg a régió kapcsolattartóit.

Wolfurti központ
+43 5574 6706-0

Az Ön kapcsolattartója

Bevásárlókosár {{ (warenkorbCtrl.warenkorb.bestellNummer ? (' [' + warenkorbCtrl.warenkorb.bestellNummer + '] ') : '' )}} | {{warenkorbCtrl.warenkorb.items.length}} Árucikkek   Bevásárlókosár váltás

Megjegyzés

Kép Árucikkek db Egységár Teljes ár Teljes ár kedvezményekkel
{{warenkorbItem.produktgruppe.produktname}}

{{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben:[{attrPrefix: 'L_', searchPattern: '/...', replacePrefix: '/', replaceSuffix: ''}] }} {{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben}}

{{attributwertEingabe.attributBezeichnung}}

     
{{hannexItem.Benennung}}

{{hannexItem.Bezeichnung}}

     

A rendelés folytatásához kérjük jelentkezzen be, hogy láthassa az árait.

Feszültségcsökkentés

Kínálatunkban szinte minden felhasználási területhez megtalálható a megfelelő anyagminőség.

M V10 PM Powder metallurgical steel

Designation

AISI:A11 (PM)

Indicatory analysis:

C2.45
Si0.90
Mn0.50
Cr5.20
Mo 1.30
V 9.75

Strength:

max. 280 HB
(≈ max. 960 N/mm²)

Thermal conductivity at 100 °C:

20 W/m K


Character:

Powder metallurgical high-speed steel with optimal dimensional accuracy after the heat treatment, highest abrasive wear resistance and excellent toughness, good machinability through a homogeneous microstructure

Application:

Blocks for eroding, dies and cutting punches with extreme requirements,
fine blanking punches, pressing punches for sinter press tools


Treatment by

highly suitable:
Polishing, nitriding, EDM, coating


Heat treatment:

Soft annealing:
880 to 900 °C, about 2 to 5 hours
slow controlled cooling of 10 to 20 °C per hour
to about 600 °C; further cooling in air, max. 280 HB

Hardening:
Curing temperature: see tempering chart
quenching in oil/compressed gas/air/hot bath
obtainable hardness: 60-63 HRC

Tempering:
slow heating to tempering temperature (to avoid forming of cracks)
immediately after hardening;
triple tempering is recommended

Tempering chart:


TechnicalTip

  • Due to the high vanadium content the steel is enriched with small, hard carbides. This guarantees optimum edge stability with maximum abrasive wear resistance.
  • Ideally suitable for highly stressed parts
    with complicated geometries.

To the mould making overview Kivágó szerszámház gyártás áttekintéséhez

Available in the web shop as:
Data sheet M V10 PM

PDF megnyitása

Material grades brochure

Material grades brochure

Material grades poster

Material grades poster

Bejelentkezés

Ön már regisztrált ügyfelünk?

Amennyiben már regisztrált a Meusburger ügyfélportálon, itt jelentkezhet be:

Elfelejtette jelszavát?

Az új jelszavát megküldtük és hamarosan meg kell érkeznie a megadott e-mail címre. Sikeres napot kívánunk Önnek!

Kérjük adja meg E-mail címét.
Új belépési jelszót küldünk Önnek.

Webáruház kiválasztása

Válassza ki országát

Telephelyek

Try our new version of 'My account'

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Keep selection
Beta
New version
Current version