Kapcsolat

Hétfőtől péntekig 8:00 és 17:00 között szívesen személyesen is állunk rendelkezésére. Ezen a linken keresztül találja meg a régió kapcsolattartóit.

Wolfurti központ
+43 5574 6706-0

Az Ön kapcsolattartója

Bevásárlókosár {{ (warenkorbCtrl.warenkorb.bestellNummer ? (' [' + warenkorbCtrl.warenkorb.bestellNummer + '] ') : '' )}} | {{warenkorbCtrl.warenkorb.items.length}} Árucikkek   Bevásárlókosár váltás

Megjegyzés

Kép Árucikkek db Egységár Teljes ár Teljes ár kedvezményekkel
{{warenkorbItem.produktgruppe.produktname}}

{{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben:[{attrPrefix: 'L_', searchPattern: '/...', replacePrefix: '/', replaceSuffix: ''}] }} {{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben}}

{{attributwertEingabe.attributBezeichnung}}

     
{{hannexItem.Benennung}}

{{hannexItem.Bezeichnung}}

     

A rendelés folytatásához kérjük jelentkezzen be, hogy láthassa az árait.

Feszültségcsökkentés

Kínálatunkban szinte minden felhasználási területhez megtalálható a megfelelő anyagminőség.

1.2162 Steel for case-hardening

Designation

DIN:21 MnCr 5
AFNOR:20 MC 5
UNI:-
AISI:5120 

Chemical composition:

C0.21
Si0.25
Mn1.25
Cr1.20

Strength:

max. 210 HB
(≈ max. 710 N/mm²)

Thermal conductivity at 100 °C:

38.5 W/m K


Character:

standard steel for case-hardening with good machinability; high surface hardness with tough core

Application:

machine parts and moulding plates with a high surface hardness;
synthetic resin press moulds for the processing of thermoplastics and thermosetting plastics.


Treatment by

possible:
Polishing, etching, EDM

Nitriding:
Usually, hardened parts are not nitrided → loss of hardness.

Hard chroming:
recommended, results in increased wear and corrosion resistance


Heat treatment:

Soft annealing:

670 to 710 °C for about 2 to 5 hours
slow controlled cooling, further cooling in air, max. 205 HB

Carburising:
900 to 950 °C. The choice of the carburising means and carburising temperature depends on the desired surface carbon content, the carburising graph and the required case depth.

Application:
870 to 930 °C in powder/salt bath, cooling in oil/warm bath at 160 to 250 °C

Intermediate stress-relieving heat treatment:
630 to 650 °C, about 2 to 4 hours with slow furnace cooling

Preheating:
350 °C depending on dimensions

Hardening:
curing temperature 810 to 840 °C in oil of ~ 60 °C warmth

Cooling:
down to about 100 °C in oil, then in air to about 50 °C

Tempering:
1 hour per 20 mm part thickness, at least 2 hours

Annealing graph:


Technical tip:
  • For mirror polishing we recommend the steel for through hardening 1.2767.

To the mould making overview Kivágó szerszámház gyártás áttekintéséhez

Available in the web shop as:
Data sheet 1.2162

PDF megnyitása

Material grades brochure

Material grades brochure

Material grades poster

Material grades poster

Bejelentkezés

Ön már regisztrált ügyfelünk?

Amennyiben már regisztrált a Meusburger ügyfélportálon, itt jelentkezhet be:

Elfelejtette jelszavát?

Az új jelszavát megküldtük és hamarosan meg kell érkeznie a megadott e-mail címre. Sikeres napot kívánunk Önnek!

Kérjük adja meg E-mail címét.
Új belépési jelszót küldünk Önnek.

Webáruház kiválasztása

Válassza ki országát

Telephelyek

Try our new version of 'My account'

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Keep selection
Beta
New version
Current version