Επικοινωνία

Βρισκόμαστε στη διάθεσή σας από Δευτέρα έως Παρασκευή από τις 8:00 έως τις 17:00. Πατήστε τον σύνδεσμο και θα βρείτε τους υπεύθυνους επικοινωνίας στην περιοχή σας.

Κεντρικά Wolfurt
+43 5574 6706-0

Ο υπεύθυνος επικοινωνίας σας

Καλάθι {{ (warenkorbCtrl.warenkorb.bestellNummer ? (' [' + warenkorbCtrl.warenkorb.bestellNummer + '] ') : '' )}} | {{warenkorbCtrl.warenkorb.items.length}} Είδος   Αλλαγή καλαθιού

Παρατήρηση

Φωτογραφία Είδος τεμ. Κόστος μονάδας Συνολικό κόστος Συνολικό κόστος συμπεριλαμβανομένης έκπτωσης
{{warenkorbItem.produktgruppe.produktname}}

{{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben:[{attrPrefix: 'L_', searchPattern: '/...', replacePrefix: '/', replaceSuffix: ''}] }} {{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben}}

{{attributwertEingabe.attributBezeichnung}}

     
{{hannexItem.Benennung}}

{{hannexItem.Bezeichnung}}

     

Συνδεθείτε για να δείτε τις προκαθορισμένες τιμές και συνεχίστε με τη διαδικασία παραγγελίας.

Lowering tension

In our selected range you can find the right material for virtually any application.

1.3343 High-speed steel (HSS)

DESIGNATION

DIN:HS 6-5-2 C
AFNOR:Z 85 WDCV 6
UNI:X 82 WMoV 6 5
AISI:M 2 reg. C

CHEMICAL COMPOSITION:

C0.9
Si0.3
Mn0.3
Cr4.0
Mo5.0
V1.9
W6.2

STRENGTH:

max. 269 HB
(≈ max. 915 N/mm²)

THERMAL CONDUCTIVITY AT 100 °C:

27.4 W/m K


CHARACTER:

high-speed steel featuring high resistance to abrasion and wear in combination with high toughness and compressive strength. High heat resistance, therefore ideal for through hardening

APPLICATION:

blocks for eroding, cold forming tools such as cutting, fine blanking and impact extrusion punches and dies
inserts with a very high wear resistance



TREATMENT BY

is possible:
Polishing

highly suitable:
Nitriding, EDM, coating



HEAT TREATMENT:

Soft annealing:
820 to 850 °C for about 2 to 5 hours
slow controlled cooling of 10 to 20 °C per hour to about 550 °C;
further cooling in air. Maximum 270 HB

Hardening:
1190 - 1230 °C
Quenching in oil/compressed gas/air/hot bath
obtainable hardness: 66 HRC

Tempering:
slow heating to tempering temperature (to avoid forming of cracks)
immediately after hardening;
triple tempering is recommended


Annealing graph:


Technical tip
  • excellent for PVD and CVD coating; highest dimensional stability because the steel was tempered at more than 520 °C.

To the mould making overview To the die making overview

Σύνδεση

Είσαστε ήδη πελάτης;

Αν έχετε ήδη στοιχεία πρόσβασης για τον ηλεκτρονικό κατάλογο της Meusburger, συνδεθείτε εδώ:

Ξεχάσατε τον κωδικό σας;

Ο κωδικός πρόσβασης σας είναι σε εξέλιξη και θα βρίσκεται σλυντομα στα εισερχόμενα σας, Σας ευχόμαστε μία δημιουργική ημέρα.

Καταχωρίστε την προσωπική σας ηλεκτρονική διεύθυνση. Θα σας αποστείλουμε νέο κωδικό πρόσβασης

Επιλογή καταστήματος

Επιλέξτε τη χώρα σας

Τοποθεσίες

Try our new version of 'My account'

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Keep selection
Beta
New version
Current version