Контакт

От понеделник до петък от 8:00 до 17:00 часа ние сме на Ваше разположение. На тази линк ще намерите лицата за контакт за вашия регион.

Централата Волфурт
+43 5574 6706-0

Вашето лице за контакти

Кошница {{ (warenkorbCtrl.warenkorb.bestellNummer ? (' [' + warenkorbCtrl.warenkorb.bestellNummer + '] ') : '' )}} | {{warenkorbCtrl.warenkorb.items.length}} Артикула   Смяна на кошницата

Забележка

Снимка Артикула Брой Единична цена Обща цена Обща цена с намалението
{{warenkorbItem.produktgruppe.produktname}}

{{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben:[{attrPrefix: 'L_', searchPattern: '/...', replacePrefix: '/', replaceSuffix: ''}] }} {{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben}}

{{attributwertEingabe.attributBezeichnung}}

     
{{hannexItem.Benennung}}

{{hannexItem.Bezeichnung}}

     

Влезте в регистрацията си, за да видите актуалните цени и да задвижите поръчката.

Намаляване на напрежението

Нашият неповторим асортимент позволява за всяка нужда подходящият материал.

1.2363 Steel for through hardening

Designation

DIN:X 100 CrMoV 5
AFNOR:Z 100 CDV 5 
UNI:X 100 CrMoV 5-1 KU
AISI:A2

Chemical composition:

C1.00
Si0.30
Mn0.50
Cr5.20
Mo1.10
V0.20

Strength:

max. 240 HB
(≈ max. 820 N/mm²)

Thermal conductivity at 100 °C:

19 W/m K


Character:

steel for through hardening with good machinability, high wear resistance and low warpage; very good dimensional stability, toughness and through hardenability

Application:

mould plates and inserts as well as cutting punches, wear plates and cutting plates with high requirements on toughness


Treatment by

is possible:
Polishing, etching, nitriding, hard chroming


Heat treatment:

Soft annealing:
800 to 840°C for about 4 to 5 hours slow controlled cooling of 10 to 20°C per hour to about 650°C further cooling in air, max. 230 HB

Hardening:
950°C to 980°C
quenching in calm air
obtainable hardness: 62 HRC

Tempering:
slow heating to tempering temperature immediately after hardening; tempering twice is recommended; rapid cooling following the tempering improves the dimensional stability;

maximum hardness achievable after tempering: 58−60 HRC

Annealing graph:

To the mould making overview To the die making overview

Available in the web shop as:
Data sheet 1.2363

Отваряне на PDF

Material grades brochure

Material grades brochure

Material grades poster

Material grades poster

Вход

Вие вече наш клиент ли сте?

Когато получите данните за достъп към портала на Meusburger, логнете се моля тук:

Забравена парола?

Ново генерираната парола е вече на път и би трябвало в кратко време да пристигне в електронната Ви поща. Желаем Ви един много успешен ден.

Моля, въведете Вашия имейл адрес.
Ние ще Ви изпратим една нова парола.

Изберете магазин

Изберете държавата в която се намирате

Местоположение

Try our new version of 'My account'

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Keep selection
Beta
New version
Current version