Контакт

От понеделник до петък от 8:00 до 17:00 часа ние сме на Ваше разположение. На тази линк ще намерите лицата за контакт за вашия регион.

Централата Волфурт
+43 5574 6706-0

Вашето лице за контакти

Кошница {{ (warenkorbCtrl.warenkorb.bestellNummer ? (' [' + warenkorbCtrl.warenkorb.bestellNummer + '] ') : '' )}} | {{warenkorbCtrl.warenkorb.items.length}} Артикула   Смяна на кошницата

Забележка

Снимка Артикула Брой Единична цена Обща цена Обща цена с намалението
{{warenkorbItem.produktgruppe.produktname}}

{{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben:[{attrPrefix: 'L_', searchPattern: '/...', replacePrefix: '/', replaceSuffix: ''}] }} {{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben}}

{{attributwertEingabe.attributBezeichnung}}

     
{{hannexItem.Benennung}}

{{hannexItem.Bezeichnung}}

     

Влезте в регистрацията си, за да видите актуалните цени и да задвижите поръчката.

Намаляване на напрежението

Нашият неповторим асортимент позволява за всяка нужда подходящият материал.

1.2311 Tool steel

Designation

DIN:40 CrMnMo 7
AFNOR:40 CMD 8
UNI:35 CrMo 8 KU
AISI:P20

Chemical composition:

C0.40
Si0.40
Mn1.50
Cr1.90
Mo0.20

Strength:

280 - 325 HB
(≈ 950 - 1100 N/mm²)

Thermal conductivity at 100 °C:

35 W/m K


Character:

alloyed and pre-toughened tool steel, especially suitable for polishing and nitriding; high dimensional stability

Application:

cavity plates, inserts and high-tensile machine parts


Treatment by

possible:
Etching, EDM

Polishing:
excellent polishing; for higher surface requirements we recommend steel for through hardening

Nitriding:
increases the steel's wear resistance

Hard chroming:
particularly increases the steel's wear resistance and corrosion resistance


Heat treatment:

already pre-toughened; usually no heat treatment required

Nitriding:
Before nitriding, stress-relief annealing is recommended at 580 °C. (Meusburger standard)

Hard chroming:
After the hard chroming the mould must be annealed about 3 to 4 hours at 180 °C to avoid brittle fractures from hydrogen.

Hardening:
840 to 860 °C

Cooling:
to 180 °C/220 °C in oil/hot bath, then in air to about 100 °C obtainable hardness: 52 HRC

Tempering:
Slow heating to tempering temperature immediately after hardening. Minimum time in furnace: 1 hour per 25 mm part thickness

Annealing graph:


Technical tip:

  • Core strength decreases with increasing plate thickness ⇒ for thickness >300, 1.2738 is recommended.

To the mould making overview To the die making overview

Available in the web shop as:
Data sheet 1.2311

Отваряне на PDF

Material grades brochure

Material grades brochure

Material grades poster

Material grades poster

Вход

Вие вече наш клиент ли сте?

Когато получите данните за достъп към портала на Meusburger, логнете се моля тук:

Забравена парола?

Ново генерираната парола е вече на път и би трябвало в кратко време да пристигне в електронната Ви поща. Желаем Ви един много успешен ден.

Моля, въведете Вашия имейл адрес.
Ние ще Ви изпратим една нова парола.

Изберете магазин

Изберете държавата в която се намирате

Местоположение

Try our new version of 'My account'

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Keep selection
Beta
New version
Current version